Multi-Sample Preparation Planning Tool
Multi-Sample Preparation Planning Tool
Plan stock solution and diluent volumes for preparing multiple research samples at a target concentration.
Use this Multi-Sample Preparation Planning Tool to calculate stock solution volume, diluent volume, total preparation volume, and per-sample volumes for laboratory research workflows. This tool is useful when preparing multiple research samples at the same target concentration.
The calculator uses the common dilution relationship C1V1 = C2V2. It helps plan how much stock solution and diluent are needed for a batch of samples, including extra overage to reduce shortage during pipetting or transfer steps.
Research Use Only: This tool is intended for laboratory research planning only. It is not intended for medical, diagnostic, veterinary, injection, dosing, or human-use guidance.
How to Use This Multi-Sample Preparation Tool
This tool is designed to make multi-sample preparation easier. Instead of calculating each sample manually, you can enter your batch details once and get the total stock and diluent volumes needed.
1. Enter a Sample or Batch Label
Start by entering a label for your preparation. This can be a batch name, plate name, experiment ID, or sample group.
Examples:
- Batch A
- Plate 1
- Control Group
- Working Solution Set 1
2. Enter the Number of Samples
Add the total number of samples you need to prepare. For example, if you are preparing 24 wells or 24 tubes, enter 24.
3. Enter Volume Per Sample
Enter the final volume needed for each sample. You can select the unit as µL or mL.
Example:
100 µL per sample4. Add Extra Overage
Overage is extra preparation volume added to reduce the risk of running short. This is useful because small amounts of liquid may be lost during pipetting, tube transfer, or plate loading.
A common research planning range is:
5% to 15% overageThe calculator allows you to set your own overage percentage based on your lab workflow.
5. Enter Target Working Concentration
Enter the final concentration you want in each sample. This is the working concentration after stock solution and diluent are mixed.
Supported concentration units include:
- mcg/mL
- mg/mL
- mcg/µL
- µM
- mM
- nM
6. Enter Stock Concentration
Enter the concentration of your available stock solution. The stock concentration must be higher than the target working concentration.
The stock and target units must also be from the same unit family. For example, use mass-based units with mass-based units, or molar units with molar units.
Valid examples:
- Stock: 1 mg/mL, Target: 100 mcg/mL
- Stock: 1 mM, Target: 10 µM
Invalid example:
- Stock: 1 mg/mL, Target: 10 µM
Mass-based and molar-based units should not be mixed in this tool because molecular weight conversion is not included here.
7. Enter Diluent or Buffer Label
Add the diluent, buffer, or solvent label used for your preparation. This field is for planning and record keeping.
Examples:
- PBS
- Sterile water
- Assay buffer
- Custom lab buffer
8. Review and Copy the Preparation Plan
After calculation, the tool will show the total preparation volume, total stock solution needed, total diluent needed, stock volume per sample, and diluent volume per sample.
You can also use the copy button to copy the preparation plan into your lab notes or worksheet.
What This Tool Calculates
The Multi-Sample Preparation Planning Tool calculates several useful values for research preparation planning:
- Total final preparation volume
- Total stock solution needed
- Total diluent or buffer needed
- Extra overage volume
- Stock volume per sample
- Diluent volume per sample
- Target concentration
- Stock concentration
- Preparation summary for lab records
Formula Used by This Tool
This tool uses the standard dilution formula:
C1V1 = C2V2Where:
- C1 = stock concentration
- V1 = stock volume needed
- C2 = target working concentration
- V2 = final preparation volume
The formula can be rearranged like this:
V1 = C2 × V2 ÷ C1After the stock volume is calculated, the diluent volume is calculated as:
Diluent volume = final preparation volume - stock volumeExample Multi-Sample Preparation Calculation
Here is a simple example.
- Number of samples: 24
- Volume per sample: 100 µL
- Extra overage: 10%
- Target working concentration: 10 µM
- Stock concentration: 1 mM
- Diluent: PBS
First, calculate the base total volume:
24 samples × 100 µL = 2400 µLThen add 10% overage:
2400 µL × 10% = 240 µL overageTotal final preparation volume:
2400 µL + 240 µL = 2640 µLNow use C1V1 = C2V2:
V1 = 10 µM × 2640 µL ÷ 1000 µMStock solution needed:
26.4 µLDiluent needed:
2640 µL - 26.4 µL = 2613.6 µLFinal preparation plan:
- Total final prep volume: 2640 µL
- Total stock needed: 26.4 µL
- Total diluent needed: 2613.6 µL
Why Overage Is Useful in Sample Preparation
When preparing multiple samples, the exact calculated volume may not always be enough in real lab handling. Small losses can happen during pipetting, mixing, tube transfer, or plate loading.
Adding a small overage helps reduce the chance of running out before all samples are prepared.
Common overage examples:
- 5% for simple preparations with low transfer loss
- 10% for routine multi-sample preparation
- 15% for workflows with more transfer steps
The right overage depends on your lab protocol, sample number, pipetting method, and preparation format.
When This Planning Tool Is Useful
This tool can help with many laboratory research workflows where the same working concentration is needed across multiple samples.
It may be useful for:
- Preparing peptide working solutions
- Planning plate-based research samples
- Preparing tube-based sample sets
- Calculating stock and buffer volumes
- Reducing manual dilution math errors
- Creating repeatable preparation notes
- Planning small-batch research workflows
Important Unit Notes
The stock concentration and target concentration must be compatible. This means both values should be from the same unit type.
Mass-Based Units
Mass-based concentration units include:
- mg/mL
- mcg/mL
- mcg/µL
Molar Units
Molar concentration units include:
- mM
- µM
- nM
Do not mix mass-based and molar-based units in this tool. If you need to convert between mg/mL and µM, use a peptide molarity calculator first and make sure molecular weight is included.
Tips for Better Multi-Sample Preparation Planning
- Check that the stock concentration is higher than the target concentration.
- Use the same unit family for stock and target concentration.
- Add a practical overage percentage to prevent shortage.
- Label the preparation with batch name, date, and concentration.
- Record the diluent or buffer used.
- Mix according to your approved laboratory protocol.
- Use calibrated pipettes for small volumes.
- Consider an intermediate dilution if the stock volume is too small to pipette accurately.
Record Keeping for Sample Preparation
Good records make research workflows easier to repeat. A simple preparation record may include:
- Sample or batch label
- Date prepared
- Number of samples
- Volume per sample
- Target concentration
- Stock concentration
- Total stock volume used
- Total diluent volume used
- Overage percentage
- Researcher initials
- Notes about handling or preparation
The copy button in the calculator can help quickly move the preparation plan into your notes.
Research Use Only Disclaimer
This Multi-Sample Preparation Planning Tool is intended for laboratory research calculations only. It is not intended for medical, diagnostic, veterinary, injection, dosing, or human-use guidance.
The results are based only on the values entered into the calculator. Always follow supplier documentation, institutional safety rules, and approved laboratory protocols.
Frequently Asked Questions
What is a multi-sample preparation planning tool?
A multi-sample preparation planning tool helps calculate how much stock solution and diluent are needed to prepare multiple research samples at a target concentration.
What formula does this tool use?
This tool uses the dilution formula C1V1 = C2V2. It calculates the stock volume needed based on stock concentration, target concentration, and final preparation volume.
What is overage?
Overage is extra volume added to the preparation to reduce the risk of running short during pipetting, transfer, or plate loading.
Can I use different units for stock and target concentration?
Yes, but they must be from the same unit family. For example, mg/mL and mcg/mL can be used together. mM and µM can also be used together. Do not mix mg/mL with µM in this tool.
Why must the stock concentration be higher than the target concentration?
This tool is designed for dilution planning. A stock solution must be more concentrated than the final working solution so it can be diluted down to the target concentration.
What should I do if the stock volume is very small?
If the calculated stock volume is difficult to pipette accurately, consider preparing an intermediate working stock according to your lab protocol.
Can this tool be used for peptide dosing?
No. This tool is only for laboratory research preparation planning. It must not be used for dosing, injection planning, treatment, or human-use decisions.
Can I copy the preparation plan?
Yes. The tool includes a copy button so you can copy the calculated preparation plan into your lab notes or worksheet.



